Concentric flue cascade C93X for condensing boilers: the collectors, boiler adapters, elbows and end pieces in PP/stainless white, from Ø60/100 to Ø200/300 mm. Inside, a PPH pipe carries the flue gas; the outer pipe in white powder-coated stainless steel supplies the combustion air: air and flue gas in one line. For gas or oil condensing boilers, flue gas up to 120 °C, negative and positive pressure. Designation EN 14471: T120 H1/P1 W2 O00 LI E U0.

Read more

What is a C93X cascade? Several condensing boilers discharge into one common concentric line: flue gas inside, combustion air outside. From the shaft, the flue gas rises through a single-wall pipe and the air comes down the shaft around that pipe. One penetration for a whole bank of boilers.

How to build the cascade? From the last boiler to the shaft:

PartCodesWhere
Cascade end pieceCONCASEK / CONCASESstart of the line: with connection for the last boiler or with drain
Boiler adapter or adapter teeCONCASKA / CONCASKAMon every boiler, from the outlet to the system diameter
Cascade collector 1 mCONCASTV60 / TV80 / TVK80one per boiler, without or with non-return valve
Pipes, adjustable pipe, elbowsCONCAS25/50/100, PP32/PP50, B15-B87connection to the shaft or the wall
Drain and inspectionCONCASCAH / CAV / IB87at the low point and at the foot of the vertical flue
Support elbow to the shaftCONCASSB87transition to the vertical flue
In the shaft (C93X)CONCASSBV / EB / AHsingle-wall black PP: support elbow with rail, end pipe, spacers
OutletCONCASMT / CONCASDDhorizontal through the wall or vertical through the roof

Which diameter? The collector must carry the flue gas of all boilers together: the diameter follows from the total output, the number of boilers, the length and the elbows (EN 13384). Send us the boilers and the layout: we calculate and draw up the parts list.

With or without non-return valve? Under positive pressure, flue gas must not enter through an idle boiler: choose the collector with valve (TVK80), unless the boilers have their own valve. Only use a valve if the boiler manufacturer allows it.

Where does the condensate go? All horizontal lines have a fall of at least 3°; the condensate is collected in the cascade end piece or drain tee and discharged through a siphon, for large outputs via a neutralisation box.

Ventichim supplies the complete concentric cascade C93X, from boiler connection to terminal, to installers throughout Belgium. Unsure about the diameter or the layout? Send us your setup: we check the cascade according to EN 13384.

Filter by:
Diameter
  • More Less
Material
  • More Less
Net weight
  • to

Concentric flue gas cascade C93X

028154.jpg
Tube 25 cm cascade C93X
028057.jpg
Tube 50 cm cascade C93X

2 variants

028056.jpg
Tube 1 meter cascade C93X

2 variants

028055.jpg
2 meter pipe cascade C93X
028149.jpg
Bend 15° cascade C93X

2 variants

028060.jpg
Bend 30° cascade C93X

2 variants

028059.jpg
Bend 45° cascade C93X

2 variants

028058.jpg
Bend 90° cascade C93X

2 variants

000977.jpg
T-piece 87° cascade C93X

2 variants

002117c.jpg
T-piece 87° with inspection end
001298.jpg
Concentric course

2 variants

028092.jpg
Inspection element cascade C93X

2 variants

028093.jpg
Inspection bend 87°
000932.jpg
Horizontal condensate drain piece

2 variants

000944.jpg
Finishing rosette cascade C93X

2 variants

028064.jpg
Centering plates cascade C93X

2 variants

Concentric pipe 25 cm PP/stainless white, cascade C93X
Concentric pipe 25 cm PP/stainless white, cascade C93X

5 variants

Concentric pipe 50 cm PP/stainless white, cascade C93X
Concentric pipe 50 cm PP/stainless white, cascade C93X

5 variants

Concentric pipe 1 m PP/stainless white, cascade C93X
Concentric pipe 1 m PP/stainless white, cascade C93X

5 variants

Concentric adjustable pipe with clamp, cascade C93X
Concentric adjustable pipe with clamp, cascade C93X

10 variants